How to Take our Peptide
Growth Hormone Releasing Peptide (GHRP) and/or Growth Hormone Releasing Hormone (GHRH) can give you an increased quality of life in ways of anti-aging, muscular development, fat loss, injury repair, higher bone density, and better sleep.
GHRP can be used on its own to increase our natural Growth Hormone (GH) pulse release from the pituitary gland in the brain. GHRP dosed in conjunction with GHRH will amplify our growth hormone release significantly to gain maximal benefit.
Before reconstitution (lyophilized / freeze dried powder):
- Can be stored in the refrigerator (2°C to 8°C = 35°F to 47°F) for 36 months.
- Can be stored at room Temperature (up to 37°C = 99°F) for 90 days.
After reconstitution (liquid):
- Can be stored in the refrigerator (2°C to 8°C = 35°F to 47°F) for 5 days.
Lifetech Labs and Lifetech Labs certified official partners always store the products in professional laboratory refrigerators. Transport time at room temperature has not effect on product quality degradation.
BIOSYNERGY NORMAL DOSAGE
Doses can be taken throughout the day but at no less than 3 hour intervals between doses.
1 dose per day is typical for light injury repair, anti-aging effects, deeper sleep, and general wellness. The most beneficial would be to dose immediately before going to bed. Sleep is the time when our pituitary is most active, the body recovers and cells repair and grow. 2 or 3 doses per day will give the added benefit of lean tissue build, muscle growth and fat loss, considering your diet consists of good quality foods.
BIOSYNERGY ADVANCED DOSAGE
- Lifetech labs recommended dosage for new users: Normal dosage (X1)
- Lifetech labs recommended dosage for advanced users (those who had already experienced with steroids, peptides or HGH): Double dose (X2)
- For some Biosynergy Blends such as Sun Beauty, Sex Boost, Recovery or Slim Fit, Lifetech labs recommended dosage for elite, competitors and professionals: Triple dose (X3). Tip: divide the injections during the day
Doses should be taken on empty stomach to benefit the most (3 hours or more). Do not consume food for between 15-30 minutes after your dosage. Best time is around 20-25 minute. GH pulses should peak within about 10 minutes after dosage. Fats and Carbohydrates affect the pulse dramatically. Protein has no effect on pulse and you can have a pure protein source in your stomach at any time.
For fat loss, your supplemental dose is 1 hour pre-cardio exercise after a long fasting without food. Best time is after waking up and before breakfast.
During cardio exercise, maintain a moderate intensity for between 30-60 minutes, 45 minutes is a good session. A moderate pace will utilize Free Fatty Acids (FFA) at the highest rate for energy. Refrain from eating for approximately 2 hours after your exercise because this is the time the body is still burning fat as fuel. You must eat throughout the day to reduce the chance of muscle catabolism (breakdown).
Peptides can be used on a daily basis for the rest of your life without any harm. Peptides is a lifestyle.
For easy and safe injections, please follow our guide below
I- RECONSTITUTE THE PEPTIDES
1. REMOVE THE VIAL CAP
If you are using a new vial, remove the protective cap (transparent plastic). DO NOT remove the stopper.
2. STERILIZE VIAL TOP
Wipe the top of the vial with an alcohol swab.
3. INJECT WATER INTO SYRINGE
Break the bacteriostatic water bottle at the blue dot and inject bacteriostatic water into the siringe.
4. INJECT WATER INTO VIAL
Put the needle through the rubber top of the vial and push the plunger to SLOWLY inject the right dosage of water into the vial:
– 2 mL of bacteriostatic water per vial for ANTI-AGING, SLIM FIT, BODY LEAN and BODY MASS.
– 1 mL for RECOVERY3, SEX BOOST and SUN BEAUTY.
II- PREPARE INJECTION
5. DRAW UP THE DOSAGE
Leave the siringe in the vial and turn both upside-down. Hold the siringe and vial firmly in one hand. Make sure the tip of the needle is in the vial.
With your free hand, pull the plunger to withdraw the correct dosage into the syringe: 0.33 mL (33 units on the insulin syringe) per injection.
6. REMOVE BUBBLES FROM SYRINGE
Hold the syringe straight up and tap the side of the syringe until the bubbles float to the top.
If bubbles are in the mix, eject air from the syringe with the plunger and draw the mix back in until you have the correct dose.
Remove the needle from the vial. Do not let the needle touch anything.
III- INJECT THE PEPTIDE BLEND
7. INJECT THE SOLUTION
Our recommended injections areas are the sames for every BIOSYNERGY Peptide Blends :